Dryer Not Heating Up? Causes, Fixes & Costs (2026)

Reading Progress:

Dryer Not Heating Up? Causes, Fixes & Costs (2026)

Key Takeaways

  • A dryer that tumbles but stays cold almost always has a failed heating element, igniter, thermostat, or a blown thermal fuse.
  • A clogged vent is the hidden cause behind most no-heat failures, because trapped heat trips the safety thermostat or fuse.
  • Professional no-heat repairs typically run $150 to $300, compared with $500 to $1,500 for a new dryer.
  • On electric dryers, a half-tripped 240-volt breaker lets the drum spin while the heat stays off entirely.
  • Home warranty plans that include laundry appliances often cover heating faults from normal wear and tear.

A dryer not heating up is one of the most common laundry failures, and the cause is usually a single electrical or airflow part rather than the whole machine. When the drum turns but clothes come out cold or damp, the heat circuit has failed: a burned-out heating element on an electric model, a dead igniter on a gas model, a tripped thermostat, or a blown thermal fuse triggered by a clogged vent. Most of these cost $150 to $300 to repair, and several have quick checks you can run before calling a technician.

Why Is My Dryer Not Heating?

A dryer that runs but does not heat has lost power to its heating circuit while keeping power to the drum motor. The heat and the tumble run on separate circuits, so one can fail while the other works. The failure is almost always a specific component — element, igniter, thermostat, or thermal fuse — not the entire appliance.

This matters because a cold dryer rarely needs replacing. The heating parts are inexpensive and standard across most major home appliances, so a targeted repair restores full function for a fraction of a new unit’s price.

Most Common Causes of a Dryer That Won’t Heat

Causes of a no-heat dryer fall into four repairable groups: a failed heating element or igniter, a tripped or failed thermostat, a blown thermal fuse, and restricted airflow from a clogged vent. Each produces the same cold-drum symptom, so a technician tests parts individually to find the fault.

Symptom Likely Cause Typical Repair Cost (2026)
Drum spins, no heat at all (electric) Failed heating element $150 to $300
Drum spins, no heat (gas), no igniter glow Failed igniter or flame sensor $150 to $280
Heat stops mid-cycle or overheats Tripped high-limit thermostat $100 to $250
Sudden total no-heat after a long cycle Blown thermal fuse $80 to $160
Weak heat, very long dry times Clogged vent restricting airflow $100 to $200

Because a clogged vent can blow the thermal fuse again after a repair, clearing the vent line is part of any lasting fix. See our dryer vent cleaning guide for the full process.

How to Troubleshoot a Dryer That’s Not Heating

Troubleshooting a no-heat dryer means ruling out the quick, free causes first — a tripped breaker, a wrong cycle setting, and a clogged vent — before assuming a failed part. Work through these steps in order, and stop once heat returns.

  1. Check the circuit breaker. On an electric dryer, confirm both halves of the 240-volt double breaker are fully on. A half-tripped breaker lets the drum spin but cuts the heating circuit. Flip the breaker fully off, then on.
  2. Clean the lint filter and vent. Remove and clear the lint screen, then disconnect and inspect the vent hose for blockage. A clogged vent is the most common reason heat shuts off and thermal fuses blow.
  3. Confirm the heat setting. Make sure the cycle is not set to Air Fluff or Air Dry, which run the drum with no heat on purpose. Switch to a timed or automatic heated cycle and test again.
  4. Listen for the gas igniter. On a gas dryer, listen for the igniter clicking and watch for a brief glow. No glow and no gas smell points to a failed igniter or flame sensor, which a technician should replace.
  5. Call for a diagnosis. If heat is still absent, the fault is likely a failed heating element, igniter, thermostat, or thermal fuse. These need a multimeter test and replacement parts, so schedule a repair or file a warranty claim.

Internal parts testing involves live 240-volt wiring on electric dryers and a gas supply on gas models, so the final diagnosis and part replacement are best left to a qualified technician or handled through a warranty claim.

How Much Does It Cost to Fix a Dryer That Won’t Heat?

A no-heat dryer repair costs $150 to $300 on average in 2026, including parts and labor. The single most expensive common fix is a gas valve coil assembly at up to $350, while a thermal fuse is the cheapest at around $80 to $160 installed. A service call alone runs $75 to $130 and is usually credited toward the repair.

Repair Part Cost Installed Cost (2026)
Diagnostic / service call — $75 to $130
Electric heating element $25 to $70 $150 to $300
Gas igniter $20 to $60 $150 to $280
Thermal fuse $10 to $30 $80 to $160
Cycling / high-limit thermostat $15 to $45 $100 to $250
Gas valve coil kit $30 to $90 $150 to $350

For comparison, a new mid-range dryer runs $500 to $1,500 installed. Appliance-repair data from Angi puts most heating-element jobs in the $150 to $300 range, which is why repair usually beats replacement for a dryer under eight years old. Our washer and dryer repair cost guide breaks down the full range by issue.

Does a Home Warranty Cover a Dryer That Stops Heating?

A home warranty is a service contract that helps cover the repair or replacement of major systems and appliances when they fail from normal wear and tear. Plans that include laundry appliances typically cover a dryer’s heating element, igniter, thermostat, and other internal parts when they wear out. Coverage depends on your plan tier and on the appliance being properly maintained.

With Empire Home Protect, a covered dryer failure is handled by filing a claim rather than paying the full repair out of pocket. Coverage is applied toward the diagnosed repair, and a covered repair is carried out by an independent service technician, subject to your plan’s terms and service fee. Because wear-and-tear failures like a burned-out heating element are exactly what warranties are designed for, laundry coverage is a practical add-on — compare plans in our 2026 home warranty rankings.

How to Prevent Dryer Heating Problems

Preventing dryer heating failures comes down to protecting airflow and reducing strain on the heating parts. Most no-heat breakdowns trace back to lint buildup, so a short maintenance routine extends the life of the element, fuse, and thermostat.

  • Clean the lint screen before every load to keep airflow strong and the heating parts cool.
  • Clear the full vent line to the exterior at least once a year, or twice if you dry daily.
  • Replace a ribbed plastic vent hose with smooth rigid metal duct to cut lint buildup.
  • Avoid overloading, which forces longer cycles and overheats the thermostat and fuse.
  • Confirm the exterior vent flap opens freely and is not blocked by debris or a nest.

Clogged vents are also a leading home fire cause, so this routine protects both the appliance and the household.

Frequently Asked Questions

Why is my dryer running but not heating?

A dryer that runs but produces no heat usually has an electrical or airflow fault: a blown thermal fuse, a failed heating element (electric) or igniter (gas), a tripped thermostat, or a clogged vent. On electric dryers, a half-tripped double breaker also cuts the heat while the drum still turns.

Is it worth repairing a dryer that won’t heat?

Repairing a no-heat dryer is usually worth it when the appliance is under 8 years old and the fix stays below $250. Most heating faults cost $150 to $300 to repair, far less than the $500 to $1,500 price of a new dryer. Past 10 years, replacement often makes more sense.

Can a clogged dryer vent cause no heat?

Yes. A blocked vent traps heat and lint, which can overheat the dryer and blow the thermal fuse or trip the high-limit thermostat, shutting off the heat as a safety measure. Clearing the vent and replacing the blown part restores heating and lowers fire risk.

How do I know if it’s the heating element or the thermal fuse?

Both cause a no-heat symptom, so a technician tests each with a multimeter for continuity. A failed heating element reads as an open circuit; a blown thermal fuse does the same but is caused by overheating, usually from a clogged vent. Replacing a fuse without clearing the vent leads to a repeat failure.

Does a home warranty cover a dryer that stops heating?

Many home warranty plans that include laundry appliances cover a dryer that fails from normal wear and tear, including heating components. Coverage depends on your plan and whether the dryer was maintained. With Empire Home Protect, you file a claim and coverage is applied toward the diagnosed repair, subject to your plan terms.

Protect Your Appliances With Empire Home Protect

A single appliance failure can cost hundreds out of pocket, and a dryer is only one of the systems that wear out over time. An Empire Home Protect plan helps cover repairs to your laundry appliances and other major home systems when they fail from everyday use. Get a free quote or compare our coverage plans to see what fits your home.

Related Articles



GET QUOTE CALL NOW